Long-cut, but very comfortable, loose-fitting dress is guaranteed to cheer up its owner. And this is not only thanks to the silhouette, wide sleeves and collar, but also to the dazzling white color of the fabric from which it is sewn. Be sure to sew such a dress for yourself, and you will always have something to wear!
Free cut dress pattern
Rice. 1. Free-cut dress - in front
Rice. 2. Free-cut dress - back
The dress pattern is modeled by. The silhouette of the dress is free, therefore, when constructing the basic pattern of the dress, the increase in freedom of fitting is 3 cm.
Modeling dress patterns
Modeling the front of the dress
Rice. 3. Modeling the front of the dress with a free cut
Transfer the bust dart on the front half of the dress to the armhole. Remove the trolley dart.
Rice. 4. Modeling sleeves, yokes and collar
Deepen the neckline by 1 cm, set aside 2 cm along the shoulder line, draw a new line for the front neckline.
Raise the shoulder line by 2 cm and lengthen the shoulder to 20 cm. Extend the shoulder line and set aside the length of the sleeve about 35-40 cm. Draw the line of the seam of the sleeve and the line of the bottom of the sleeve at a right angle. The width of the half sleeve at the bottom is 15 cm.
Build a front yoke 4 cm wide. Cut the yoke and cut it out separately. Draw a side line as shown in fig. 4, having narrowed the dress to the bottom by 2 cm. The length of the dress from the waist is about 55 cm.
Modeling the pattern of the back of the dress
Rice. 5. Free-cut dress - back modeling
The back pattern is modeled on the basis of the front pattern. Remove the trolley dart. Deepen the neck of the back by 1 cm. Set aside 2 cm along the shoulder. Draw a new line for the neck of the back.
Place the front pattern on the back pattern, reshoot the sleeve and back side line as shown in fig. 5.
Collar pattern
Measure the length of the front and back necklines along the pattern. Draw a rectangle equal to ½ of the neckline of the dress and 9 cm wide (see Fig. 4). Set aside 2 cm from the left corner of the rectangle to the right, from the bottom left corner up and from the top right corner down.
Connect the resulting points, slightly rounding the top and bottom lines of the collar. Cut out the collar with a fold (2 parts).
Advice! The collar can also be cut into a rectangle with a fold at the top. In this case, the width of the part will be 14 cm (7 cm in finished form), the length is equal to the length of the neckline of the dress according to the pattern. In this case, the collar is cut along an oblique thread.
Dress cut details
Details of the dress are shown in Fig. 6.
For the dress you will need: 1.5 m of white jersey, 145 cm wide, thin thermal fabric for jersey, threads.
Cut out from the main fabric:
11. Backrest - 1 piece with a fold
12. Before - 1 piece with a fold
13. Front yoke - 2 parts
14. Sleeve - 2 pieces with a fold
15. Collar - 2 folds.
Cut out all details with allowances for seams and hem by 1.5 cm, allowances for the bottom of the dress and sleeves - 4 cm.
How to sew a dress
Sew the details of the yokes to the details of the front, overlap the allowances. Stitch the yokes from the front side at a distance of 0.7 cm from the seam.
Sew shoulder seams, sew on sleeves, process allowances. Stitch side seams, fold over the hem of the dress and sew with machine blind stitch.
Fold over allowances at the bottom of the sleeves and hem them with a machine blind stitch.
Duplicate the outer collar with a thin thermal fabric for knitwear, stitch along the short side, iron the allowances. Sew the second collar part (inner) on the short side, iron the allowances.
Fold both collars right sides, stitch along the top edge, turn out, sweep the top edge. Sew the collar into the neckline, sew in with an elastic overfill seam.
Your loose-fitting dress is ready! Wear it with pleasure and be happy!
Fashion designer
Hello dear readers!
The goal of our tutorial is to learn how to model dresses based on a basic pattern. The kind that beginners can handle. In addition, we will analyze simple styles of dresses, suitable for your type of figure, on the example of which you can, if you want, create more complex models, enriching them with details and using a combination of fabric textures and colors.
Sometimes they write to us: “It's very difficult for me to buy ready-made clothes, my figure is an inverted triangle, besides, I have a very decent bust and a wide chest, that is, my chest volume is 102 cm - this is a very big disappointment for me. I have the opportunity to purchase any thing for myself, because the rest of the parameters of the figure go to 44-46 sizes ... What style can you choose? "
Of course, having parameters that do not fit into the framework of standards, it is difficult to find something in the store to your liking, and sometimes going for a new thing turns into one frustration. Well, there is no need to be sad, especially to a person who has at least a little experience in sewing clothes. And with patterns, simple, such that even a novice tailor can create, we will try to help. It's no secret that everyone in the world sews dresses using one universal pattern, modifying and modeling it. Having in your arsenal such an invaluable tool, the creation of which on our website does not take much time, you will be able to dress according to your taste and image invented by you.
First, what is a basic pattern? This is a pattern without model features, roughly speaking, it is a human figure made in a two-dimensional plane. The pattern has a different degree of fitting, depending on what type of clothing will be designed in the future - top (coat, jacket) or light (dress, blouse, corset, etc.), and differs in the amount of increase in freedom. Therefore, on our website you will find and, as well, they will differ in increments, which is very important. By the way, on our site, along with the possibility of building a basic pattern according to individual sizes, there are a number of already models of dresses that are absolutely different in cut and suitable for women of different types of figures. You can also use them, especially since each size is presented in three heights, and this is very important for a good fit of the finished product.
So, having a base pattern in our hands, we can proceed directly to modeling. First, let's choose a dress model. This point must be treated very responsibly, objectively assessing your appearance, figure, image as a whole. After all, it is no secret that we are all different people, each of us has its own individual figure, which sometimes does not fit into the so-called "ideal framework", especially since this very ideal is different in every time interval, it changes according to fashion trends. Let's not adjust ourselves to the standards and love our individuality. All female figures are conventionally divided into several body types, and each of us belongs to one type or another to a greater or lesser extent.
Illustration from the site https://high-fashion21.ru
Modeling a dress for the shape type "Triangle" (pear)
The pear-shaped figure is very feminine, but sometimes it brings the owner some difficulties when choosing a ready-made dress due to the difference in the girth of the hips and chest. Don't be upset. First, let's figure out which style to choose. We narrow the bottom and focus on the upper part: a boat-shaped neckline, a large collar, a neckline, a bright print in the upper part of the dress, the bottom can be slightly flared, do not forget about the use of contrast inserts running along the dress and visually modeling the figure, as well as a little High waist, heels and tights to match the shoes will make you slimmer. We try to avoid decorations in the area of hips, patch pockets, draperies, cross stripes and large prints.
For an example of modeling, we will choose a simple sheath dress created on. The style is interesting in that the model lines that form the silhouette are the best and most advantageous way to demonstrate the female figure of the lower type. Dark inserts running along the side seams will help to visually hide the width of the hips, and the white, expanding silhouette at the top will highlight the slimmer silhouette. But, here it is impossible to be too clever with excessive narrowing of the skirt and if the difference between the girths of the chest and hips is large, it is better to widen the skirt a little towards the bottom.
Modeling. On the details of the pattern of the back and the shelf, draw model lines of reliefs passing from the armholes to the bottom of the dress through the waist darts, on the back, transfer part of the solution to the middle line of the back, for the best fit in this area. Open the bust dart in the armhole, read more about the transfer of darts here. It remains only to outline the allowance for the slot. If the difference between the waist and hip girth is large and the solutions of the darts for fitting are more than 3-3.5 cm each, the dart must be split into two, otherwise ugly creases in the waist area will appear in the finished product.
In the second version of modeling, we propose to expand the skirt to the bottom, make it the so-called A-silhouette, you can also make the dress cut-off at the waist.
Modeling a dress for the "Inverted triangle" body type
Your strong point is narrow hips and long, slender legs. We focus on them. All decor, bright prints - down to the skirt. Reducing the width of the shoulders, here raglan sleeves will help us, or the absence of sleeves at all in summer clothes, a dress with a strap on one shoulder, a Greek silhouette, a loose tunic, a dress with a tulip skirt can become a lifesaver and be loved in your wardrobe. You can afford to wear fluffy wide skirts, skirts or trousers with a peplum, straight cut dresses, but not too voluminous and wide, with vertical seams or trim.
As an example, we will analyze the modeling of a pattern of a simple dress suitable for this type of figure. The model has a fitted sleeveless bodice and a tulip skirt that adds volume to the hips. The dress is cut-off along the waist line, there are two opposite folds on the front panel of the skirt, and a slit is made on the back panel of the skirt.
We start modeling by applying to the details of the backrest and shelf. embossed lines (if you want a greater fit or the fabric is knitted, you can use the base pattern of the adjacent silhouette). We will arrange the thallium darts on the front panel of the skirt into folds - cut the skirt part from the end of the darts vertically downwards, move the parts apart so that in the upper part we obtain a solution approximately equal to 6-8 cm to form deep counter folds. At the bottom, keep the volume of the skirt in its original form.
Modeling a dress for the "Hourglass" figure type
The "hourglass" type of figure is the most feminine, it is he who is rightfully considered a standard for imitation and we try to bring our figure closer to it, at least with the help of clothes. Lucky women with this type of physique. The main advice is to focus on the waist, so you will further emphasize your femininity and sexuality. Neckline, bows, pencil skirts, stilettos - this is your win-win image.
Let's simulate such a simple dress, in two versions.
The model is quite simple at first glance, but with the right choice of fabric and accessories, it is very effective.For modeling we need and ... Cut-off dress along the waist line, the skirt is widened to the bottom. The darts for fitting the chest are transferred into the neckline: in the first version, the darts from the neck are stitched with an allowance outward, a small sleeve with a fold, in the second version, the darts on the chest are distributed in folds extending from the neckline, there are no sleeves.
Modeling. 1 step - on the details of the back, the dart for the roundness of the shoulder can be neglected, because the neckline of the back is deep enough and widened, but the size of the solution must be removed from the length of the shoulder so as not to upset the balance. For the convenience of modeling, we will transfer the dart on the shelf to the armhole. Cut the details of the skirt pattern lengthwise from the darts down.
Next, step 2 of the simulation. Draw a new line for the neckline according to the sketch. We will transfer the tallium dart on the shelf to the neckline, and we will also transfer the dart from the armhole there. Learn more about translating darts. When designing a detachable adjacent silhouette, the pattern of the shelf part must be lowered in the waist area by 1 cm, this will give a better fit and prevent it from jerking when finished. Skirt. We connect the parts of the pattern obtained after cutting the details of the skirt, so that the darts open to the bottom. Correct the side cuts and the bottom of the product.
Sleeve modeling. The pattern of the base of the sleeve can be taken on ours. First, let's shorten the length to the required one. With the help of vertical cuts going from the ridge to the bottom of the part, and the subsequent spreading of the parts of the pattern, design the opposite fold.
More sleeve modeling can be found in this
In the second version of the dress, the darts on the shelf are transferred into folds extending from the neckline. We will consider modeling below.
Modeling a dress for the "Oval" shape type (apple)
The figure is an oval (apple). In the era of Rubens, women with this type of figure were the ideal of perfection. The silhouette is visually close in shape to the letter "o". The strategy in choosing the right clothes will be to emphasize, accentuate the waist, this can be done by choosing a dress that slightly expands to the bottom, as well as the use of belts, decorative inserts that make the waist visually narrower, the top of the dress should be slightly expanded, for example, use a V-neck, collars ... Sheath dresses, smells, low waist, A-line dresses will suit you.
As an example, let's take a look at this dress. It is interesting because it has a contrasting decorative line running along the dress. Visually, this is very stretching the silhouette and slimming. In addition, the dress is loose in the waist area and slightly widens towards the bottom, which is undoubtedly a plus for this type of figure. Clear cut lines and the choice of fabric that keeps its shape, create the desired image and collect the figure as a whole. To simulate this model, we will use , for a better fit.
Modeling. Straighten the side cuts of the parts, because the dress has a straight free silhouette. Move the dart on the breast bulge to the side seam and outline the relief line. We will shorten the pattern of the sleeve detail just above the elbow.
In the received details, outline the front yoke and cut it off.
Modeling a dress for the "Rectangle" shape type
The female figure is a rectangle type. It is the most typical for modern models. Therefore, when buying ready-made clothes, usually there are no problems, but sometimes you really want something special! This is where our modeling tips and patterns can come in handy!)) Women with this body type do not need to try to look like Merlin Monroe or Sophia Loren, this is not your style. Dresses and clothes in the image of Twiggy, Kate Moss, Nicole Kidman and Coco Chanel herself are what we are striving for.
We chose the dress for the modeling lesson just right. We need the pattern this time. Sleeveless dress, loose cut with a counter fold going down from the neckline, fastened at the bottom to give the product an oval silhouette. Pockets can be made in the side seams.
Today, more than ever, simplicity of cut of clothes is in trend. The loose dress has been a hit for several seasons in a row. Only the density of the material, the decor change, and some modeling moments are introduced, but basically the cut remains unchanged. The pattern of a loose dress is quite simple to build, so even the most inexperienced seamstress can cope with sewing such a product. Of course, you can easily go to the store and buy the finished product. But self-tailoring has a lot of advantages, the main of which is the cost, which allows you to pamper yourself with a couple of new things for the same money. How to sew a loose dress at home will be discussed further.
Material selection
It is best to sew a loose dress from knitted fabric. It should be chosen based on the time of year. For winter, you can take angora or wool, for spring and autumn - diving, footer, jersey, for summer, stretch cooler and micro oil are ideal. Also, in the work, you can use dress fabrics with a transverse stretch. The advantage of stretch fabrics is that they wrinkle less. And given that the free dress is wide enough, this fact plays in favor of the appearance of the thing.
Preparation for sewing
Calculations and taking measurements are an integral part of the process of creating blanks for any product. The pattern of a loose dress is built on the basis of the following measurements of the figure:
- the volume of the chest, waist and hips;
- chest height;
- back and shoulder width;
- the height of the back and front to the waist;
- length of the product;
- upper arm girth;
- neck circumference.
All measurements should be written down on a piece of paper so that it is easier to transfer them to the drawing.
Pattern creation
A loose dress, as a rule, has either an A-line shape or a straight silhouette. The template for both models is the same, and all additional elements are built during the modeling process. The template is best done on a piece of wallpaper or construction film. The latter option is more practical if you plan to create not one, but several dresses.
So, in order to sew a free one, you will first need to develop a pattern based on the measurements taken. First, you should draw a rectangle in which half of the back and half of the front will be built. The upper and lower sides should be equal to half of the chest circumference, and the side - the length of the product. From the upper corner, you need to retreat by the size of the measurements "chest height" and "back and front height to the waist" and draw additional horizontal lines. The first will be the chest line and the second will be the waistline. Another 20 cm should be retreated from the latter and the line of the hips should be marked. Continuing to create the basic mesh, note the width of the back and calculate the width of the armhole to draw additional verticals. To do this, along the chest line from the left side of the rectangle, the value of the "back width" measure is retreated and the point from which the armhole begins is set. To calculate its length, you need to divide half of the breast volume by 4 and add 2 cm. This value is also marked on the chest line and put a dot. The rest will belong to the front shelf.
Next, proceed to the designation of the shoulder seams and the neckline. Here everything is quite simple: the value corresponding to half of the neck circumference recedes from the upper corners and the shoulder area is highlighted. In this case, the extreme point should be underestimated by 1 cm, and from the side of the back, the rounding of the neck should be raised by 1 cm, and the shoulder seam is also drawn with a bevel of 1 cm. point, connecting it to the edges of the shoulder seams. From this central point, the side seams are lowered down, which are slightly pulled apart to the sides to the bottom line, in accordance with the volume of the hips.
A free dress eliminates tuck darts, which simplifies the construction of a template. However, if the fit does not suit, the product can be slightly fitted from the back.
Build a sleeve
For a loose fit, it will be enough to process the armhole. A warmer version will need to be supplemented with a sleeve. It can be one-piece or set-in. They are built in different ways. If you continue the shoulder seam and, having cut the details of the base of the dress along the side seam, remove the lower cut of the sleeve from it, a one-piece version will come out. For the set-in sleeve, you will need to fold the base parts along the shoulders and transfer the cut of the armholes to a separate sheet for the drawing. After the upper rounding, you will need to rise by 1.5 cm and draw a circle based on the contour of the resulting line. Along the lower border of this figure, in the center, you should place the measurement of the girth of the upper arm and draw an okat descending along the boundaries of the circle and reduced to a straight line.
Decorative elements
The dress will come out really sophisticated if the decor is used correctly. For example, plain knitwear can be diluted with lace inserted into the shoulders or around the neckline. You can also play with a contrasting combination of canvases of the same quality. Loose dresses, photos of which are presented in the article, have various decorative decorations that can serve as an example or become for more interesting design ideas.
In addition to the standard decoration options, you can experiment with textures. For example, make a dress with a light chiffon collar and sleeves with mother-of-pearl buttons. In combination with dark knitwear, this dress will be an excellent office option.
Do not forget about such elements as pockets, they will perfectly complement loose dresses. Photos of finished products on the models will allow you to determine the most appropriate location of these elements. Slotted, laid on and with a leaf, decorated with rag roses, rhinestones and sewing stones on a strict silhouette of a wide cut, they will look very harmonious and make the image interesting and stylish.
Assembling parts
In order for the product to come out of high quality, you need to sew all its elements in the correct sequence. First of all, work is carried out with the front shelf, in particular, pockets and other model elements are made out. Next comes the turn of the shoulder seams and stitching on the sleeves. After that, the side sections are closed and the trim is sewn to the neckline. Next comes the turn of processing the bottom of the sleeves and the hem.
Greetings to all ladies who love beautiful elegant clothes and are ready to create their own wardrobe with their own hands! The dress is gaining another round of popularity, despite the dominance of trousers, in this respect, the most versatile model that will suit almost everyone.
The straight dress with three-quarter sleeves in style is very versatile and will come in handy for a wide variety of situations. Its simplicity is its advantage. It is laconic and elegant. Side seam pockets make it more comfortable and interesting. The two-seam sleeve creates a good and comfortable fit on the arm.
You can choose different materials for such a model. It all depends on what kind of result you want to get. From dense materials such as cotton or jacquard, the dress will look more statuesque and keep its shape well. From soft fabrics such as silk or wool, it will not look so severe.
MAIN SIZES FOR THE PATTERN
Chest circumference - 96 cm
Waist girth - 78 cm
Hips circumference - 102 cm
MATERIALS FOR WORK
Fabric 150 cm wide and 160 cm long
Non-woven
Concealed zip length 22 cm
PATTERN DETAILS
1 - Shelf (one piece with a fold)
2 - Backrest (two parts)
3 - Front part of the sleeve (two parts)
5 - Burlap pocket (four parts)
The pattern is given without seam allowances. Along all the cuts, add 1.5 cm each, along the bottom of the sleeves - 3 cm, along the bottom of the dress - 4 cm.
WORK DESCRIPTION
1. Stitch center seam along back. Process the sections and iron them out.
2. Sew in a hidden zipper. Look.
3. Sew shoulder seams. Process them and iron them on the shelf.
4. Cut out the piping on the basis of the top of the shelf as a separate piece and duplicate it with non-woven fabric.
5. Trim the neck as shown in.
6. Sew chest darts on the shelf and press them down.
7. Sew side seams, leaving room to enter pockets.
8. Sew pockets in the side seams. To help .
9. Finish the allowance at the bottom of the dress and iron it to the wrong side. ...
10. Sew elbow and front seams on sleeves. Process and iron.
11. Finish the bottom cuts of the sleeves and iron the seam allowances on the wrong side. Sew by hand with blind stitch.
12. Sew sleeves into armholes. Process the allowance.
The dress is ready!
The pattern of this model is quite simple and on its basis you can sew a lot of interesting products, even combining several diverse materials.
Women's dress of a straight silhouette with a three-quarter sleeve is suitable for ladies of all ages. For young girls, you can make it from bright fabrics with beautiful decorations. For ladies of a more mature age, these can be more calm, restrained options that will look very good.
Fashionable women's dresses are varied, but there are basic models that have become classic, which always remain relevant. This dress is just one of them. It will be a great addition to any wardrobe. By the way, if you make it short, then it may well play the role of a tunic.
Subscribe to the news and stay in touch to find out a lot more useful and interesting things!
Find out even more interesting things:
Sleeveless light summer dress
Greetings to all fashionistas and lovers of comfortable and beautiful clothes! I would like to present to your attention a light sleeveless summer dress. This model, despite its ...
Plus size straight long summer dress
Greetings to all sewing lovers! In the summer, many women, reviewing their wardrobe, think about whether to replenish it with something new. ...
The pear-shaped figure is very feminine, but sometimes it brings the owner some difficulties when choosing a ready-made dress due to the difference in the girth of the hips and chest. Don't be upset. First, let's figure out which style to choose. We narrow the bottom and focus on the upper part: a boat-shaped neckline, a large collar, a neckline, a bright print in the upper part of the dress, the bottom can be slightly flared, do not forget about the use of contrast inserts running along the dress and visually modeling the figure, as well as a little High waist, heels and tights to match the shoes will make you slimmer. We try to avoid decorations in the area of hips, patch pockets, draperies, cross stripes and large prints.
photo from the site, http://www.chieflady.com/
For an example of modeling, we will choose a simple sheath dress created on a pattern based on an adjacent silhouette. The style is interesting in that the model lines that form the silhouette are the best and most advantageous way to demonstrate the female figure of the lower type. Dark inserts running along the side seams will help to visually hide the width of the hips, and the white, expanding silhouette at the top will highlight the slimmer silhouette. But, here it is impossible to be too clever with excessive narrowing of the skirt and if the difference between the girths of the chest and hips is large, it is better to widen the skirt a little towards the bottom.
photo from the site http://www.stylishwife.com/
Modeling. On the details of the pattern of the back and the shelf, draw model lines of reliefs passing from the armholes to the bottom of the dress through the waist darts, on the back, transfer part of the solution to the middle line of the back, for the best fit in this area. Open the bust dart in the armhole, read more about transferring the darts. It remains only to outline the allowance for the slot. If the difference between the waist and hip girth is large and the solutions of the darts for fitting are more than 3-3.5 cm each, the dart must be split into two, otherwise ugly creases in the waist area will appear in the finished product.
In the second version of modeling, we propose to expand the skirt to the bottom, make it the so-called A-shaped silhouette, you can also make the dress cut-off at the waist.
MODELING A DRESS FOR THE INVERTED TRIANGLE FIGURE
Your strong point is narrow hips and long, slender legs. We focus on them. All decor, bright prints - down to the skirt. Reducing the width of the shoulders, here raglan sleeves will help us, or the absence of sleeves at all in summer clothes, a dress with a strap on one shoulder, a Greek silhouette, a loose tunic, a dress with a tulip skirt can become a lifesaver and be loved in your wardrobe. You can afford to wear fluffy wide skirts, skirts or trousers with a peplum, straight cut dresses, but not too voluminous and wide, with vertical seams or trim.
photo from the sites http://refinedstylefashion.com/ https://ru.pinterest.com/pin/454089574910263523/ http://stylowi.pl/
As an example, we will analyze the modeling of a pattern of a simple dress suitable for this type of figurus. The model has a fitted sleeveless bodice and a tulip skirt that adds volume to the hips. The dress is cut-off along the waist line, there are two opposite folds on the front panel of the skirt, and a slit is made on the back panel of the skirt.
photo from the site http://snowqueen.ru/
We begin modeling by applying the basic pattern of the adjacent silhouette to the relief lines on the details of the back and the shelf (if you want a greater fit or the fabric is knitted, you can use the base pattern of the adjacent silhouette). We will arrange the thallium darts on the front panel of the skirt into folds - cut the skirt part from the end of the darts vertically downwards, move the parts apart so that in the upper part we obtain a solution approximately equal to 6-8 cm to form deep counter folds. At the bottom, keep the volume of the skirt in its original form.
MODELING OF THE DRESS FOR THE "HOURGLASS" FIGURE
The "hourglass" type of figure is the most feminine, it is he who is rightfully considered a standard for imitation and we try to bring our figure closer to it, at least with the help of clothes. Lucky women with this type of physique. The main advice is to focus on the waist, so you will further emphasize your femininity and sexuality. Neckline, bows, pencil skirts, stilettos - this is your win-win image.
photo from sites http://www.asos.com/ https://ru.pinterest.com/NatalieYoung29/
Let's simulate such a simple dress, in two versions.
photo taken from sites
The model is quite simple at first glance, but with the right choice of fabric and accessories, it is very effective. For modeling, we need a pattern for the base of an adjacent silhouette and a pattern for a sleeve. Cut-off dress along the waist line, the skirt is widened to the bottom. The darts for fitting the chest are transferred into the neckline: in the first version, the darts from the neck are stitched with an allowance outward, a small sleeve with a fold, in the second version, the darts on the chest are distributed in folds extending from the neckline, there are no sleeves.
Modeling. 1 step - on the details of the back, the dart for the roundness of the shoulder can be neglected, because the neckline of the back is deep enough and widened, but the size of the solution must be removed from the length of the shoulder so as not to upset the balance. For the convenience of modeling, we will transfer the dart on the shelf to the armhole. Cut the details of the skirt pattern lengthwise from the darts down.
Next, step 2 of the simulation. Draw a new line for the neckline according to the sketch. We will transfer the tallium dart on the shelf to the neckline, and we will also transfer the dart from the armhole there. Learn more about translating darts. When designing a detachable adjacent silhouette, the pattern of the shelf part must be lowered in the waist area by 1 cm, this will give a better fit and prevent it from jerking when finished. Skirt. We connect the parts of the pattern obtained after cutting the details of the skirt, so that the darts open to the bottom. Correct the side cuts and the bottom of the product.
Sleeve modeling. The sleeve base pattern can be taken on our website. First, let's shorten the length to the required one. With the help of vertical cuts going from the ridge to the bottom of the part, and the subsequent spreading of the parts of the pattern, design the opposite fold.
In the second version of the dress, the darts on the shelf are transferred into folds extending from the neckline. We will consider modeling below.
MODELING A DRESS FOR THE TYPE OF OVAL FIGURE (APPLE)
The figure is an oval (apple). In the era of Rubens, women with this type of figure were the ideal of perfection. The silhouette is visually close in shape to the letter "o". The strategy in choosing the right clothes will be to emphasize, accentuate the waist, this can be done by choosing a dress that slightly expands to the bottom, as well as the use of belts, decorative inserts that make the waist visually narrower, the top of the dress should be slightly expanded, for example, use a V-neck, collars ... Sheath dresses, smells, low waist, A-line dresses will suit you.
photo from the sites http://yourmothershouldknow.tumblr.com/ https://ru.pinterest.com/buyerselect/ https://ru.pinterest.com/nordstrom/ http://dresses-photo.ru/ http: / /jenskie-hitrosti.ru/
As an example, let's take a look at this dress. It is interesting because it has a contrasting decorative line running along the dress. Visually, this is very stretching the silhouette and slimming. In addition, the dress is loose in the waist area and slightly widens towards the bottom, which is undoubtedly a plus for this type of figure. Clear cut lines and the choice of fabric that keeps its shape, create the desired image and collect the figure as a whole. To model this model, we will use a basic sewing pattern of an adjacent silhouette for a better fit.
photo from the site
The female figure is a rectangle type. It is the most typical for modern models. Therefore, when buying ready-made clothes, usually there are no problems, but sometimes you really want something special! This is where our modeling tips and patterns can come in handy!)) Women with this body type do not need to try to look like Merlin Monroe or Sophia Loren, this is not your style. Dresses and clothes in the image of Twiggy, Kate Moss, Nicole Kidman and Coco Chanel herself are what we are striving for.
photo from sites http://ouiliviamoraes.com/ http://my.goodhouse.com.
Modeling takes place on the basic pattern-based dress of a straight silhouette, without darts. To begin with, we will get rid of the dart on the back, on the shelf we will complete the depth of the fold, setting aside a distance of 12-15 cm from the middle of the part.Please note that one opposite fold is laid on top of the dress, while at the bottom there are two of them - one-sided, the depths are laid towards the side seams. The side seam lines are designed to create an oval silhouette. This model should be long above the knee, otherwise there may be excessive narrowing at the bottom.
Well, our lesson has come to an end, we have learned how to create simple dress patterns based on the basic pattern, such that beginners can handle the modeling and sewing, and talked about the types of figures. I think now you can please yourself with a new thing. Good luck and creative mood!
